Zinc and sulfur functionalized biochar as a peroxydisulfate activator via deferred ultraviolet irradiation for tetracycline removal.

To enhance the degradation of tetracycline class (TC) residuals of high-concentration from pharmaceutical wastewater, a novel zinc (Zn) and sulfur (S) functionalized biochar (SC-Zn), as a peroxydisulfate (PDS) activator, was prepared by two-step pyrolysis using ZnSO4 accumulated water-hyacinth. Results showed that the removal rate of 50, 150, and 250 mg per L TC reached 100%, 99.22% and 94.83% respectively, by the SC-Zn/PDS system at a dosage of 0.3 g per L SC-Zn and 1.2 mM PDS, via the deferred ultraviolet (UV) irradiation design. Such excellent performance for TC removal was due to the synergetic activation of PDS by the biochar activator and UV-irradiation with biochar as a responsive photocatalyst. The functionalization of the co-doped Zn and S endowed the biochar SC-Zn with a significantly enhanced catalytic performance, since Zn was inferred to be the dominant catalytic site for SO4˙- generation, while S played a key role in the synergism with Zn by acting as the primary adsorption site for the reaction substrates. The employed SC-Zn/PDS/UV system had excellent anti-interference under different environmental backgrounds, and compared with the removal rate of TC by adsorption of SC-Zn, the increasing rate in the SC-Zn/PDS/UV system (18.75%) was higher than the sum of the increases in the SC-Zn/PDS (9.87%) and SC-Zn/UV systems (3.34%), furtherly verifying the systematic superiority of this synergy effect. This study aimed to prepare a high-performance functionalized biochar activator and elucidate the rational design of deferred UV-irradiation of PDS activation to efficiently remove high-concentration antibiotic pollutants.

Influence of protonic acid on the structure and properties of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) in oxidation polymerization.

Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is widely used because of its excellent performance. We report the synthesis of two PEDOT:PSS dispersions. The two dispersions differ by the addition of additional protonic acid in the oxidative polymerization system. Although there are examples of the introduction of acids into the polymerization system, the effects of acid on the structure and properties of these materials, in particular their mechanisms of action, have not been elucidated. We describe the chemical structure and molecular weight of two PEDOT polymers using Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, UV-vis-NIR spectroscopy, and density functional theory calculations. The carrier concentration, carrier mobility, and surface morphology of the composites are characterized by UV-vis-NIR spectroscopy, electron spin resonance, Raman spectra, Hall effect measurements, and atomic force microscopy. The crystallinity of PEDOT:PSS was measured by X-ray diffraction patterns. We show that the addition of a proper amount of protonic acid to the oxidative polymerization system can effectively reduce the formation of the terminal carbonyl group of PEDOT chains, which is conducive to the growth of polymer chains, and further improve the carrier concentration, which leads to an improvement of conductivity. Our results highlight the optimization of the chemical structure of PEDOT in order to increase its molecular weight and ultimately its conductivity.

Preparation of water-dispersed monolayer LDH nanosheets by SMA intercalation to hinder the restacking upon redispersion in water.

We present a novel method for preparing water-dispersed monolayer layered double hydroxide (LDH) nanosheets (m-LDH). By intercalating styrene-maleic anhydride copolymer (SMA) into LDH, we obtained m-LDH through a simple aging step that produced stable, translucent colloidal solutions. After drying, the resulting powder can be redispersed in water to recover the m-LDH monolayer structure. To our knowledge, this is the first report of immediate recovery of the m-LDH monolayer structure from dried powder after redispersion in water. Our method may have significant implications for preparing and utilizing m-LDH nanosheets in various applications.

Flame retardant properties and mechanism of PLA/P-PPD -Ph /ECE conjugated flame retardant composites.

In this article, 4, 4'-{1'',4''-phenylene-bis[amido-(10'' ''-oxo-10'''-hydro-9'''-oxa-10'''λ5-phosphafi-10'''-yl)-methyl]}-diphenol (P-PPD-Ph) was synthesized by a two-step synthesis, followed by the addition of various levels of epoxy chain extender (ECE) with 5 wt% of P-PPD-Ph The PLA/P-PPD-Ph/ECE conjugated flame retardant composites were produced by co-extrusion into poly(lactic acid) (PLA). The chemical structure of P-PPD-Ph was characterized by FTIR, 1H NMR and 31P NMR tests, demonstrating the successful synthesis of the phosphorus heterophilic flame retardant P-PPD-Ph. The structural, thermal, flame retardant and mechanical properties of the PLA/P-PPD-Ph/ECE conjugated flame retardant composites were characterised using FTIR, thermogravimetric analysis (TG), vertical combustion testing (UL-94), limiting oxygen index (LOI), cone calorimetry, scanning electron microscopy (SEM), elemental energy spectroscopy (EDS) and mechanical properties testing. The structural, thermal, flame retardant and mechanical properties of PLA/P-PPD-Ph/ECE conjugated flame retardant composites were characterised. The results showed that with the increase of ECE content, the residual carbon rate of the composites increased from 1.6% to 3.3%, and the LOI value increased from 29.8% to 32.6%. The cross-linking reaction between P-PPD-Ph and PLA and the increase of reaction sites led to the generation of more phosphorus-containing radicals on the PLA molecular chain, which strengthened the cohesive phase flame retardant effect of PLA flame retardant composites, and The bending strength, tensile strength and impact strength were all improved.

Flame-retardant properties and mechanism of LGF/PBT/DOPO-HQ-conjugated flame-retardant composites.

In this article, long fiber reinforced polybutylene terephthalate (LGF/PBT/DOPO-HQ) flame-retardant composites were prepared using 10-(2,5-dihydroxy phenyl)-10H-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO-HQ) as the conjugated flame-retardant. The effects of different flame-retardant contents on the combustion properties of the composites were investigated. The results showed that after adding 14% of DOPO-HQ, the flame-retardant effect of the composite reached the V-0 level of UL-94 fire rating with an ultimate oxygen index (LOI) of 26.4%. The average heat release rate (Av-HRR), peak heat release rate (PHRR), and total heat release rate (THR) decreased by 45.9, 56.5, and 32.6%, respectively. This shows that LGF/PBT/DOPO-HQ composite has good flame-retardant properties. Meanwhile, the flame-retardant mechanism of cohesive phase and gas-phase synergy during the combustion of flame retardants was analyzed by carbon layer morphology and dynamic thermal decomposition.

Terminal group effects of DOPO-conjugated flame retardant on polyamide 6: Thermal stability, flame retardancy and mechanical performances.

Two DOPO-conjugated flame retardants with or without amino terminal groups (DOPO-NH2 and DIDOPO, respectively) were synthesized and incorporated into polyamide 6 (PA6). Results demonstrated the DOPO-NH2 endowed superior thermal, flame retardant and mechanical performances to PA6 composites. With the same loading of 15 wt%, DOPO-NH2 can catalyze the PA6 matrix more effectively and result in more residues at high temperature. The PA6 composites containing DOPO-NH2 exhibited higher LOI (28.0%) compared to 25.0% for the sample containing DIDOPO, and the lower heat release capacity and peak heat release rate. Furthermore, the overall mechanical properties of PA6 composites containing DOPO-NH2 outperformed the samples containing DIDOPO, even superior to that for PA6. Such a significant difference can be mainly attributed to the existence of amino-terminal group, which can interact with carboxyl group in PA6 as confirmed by dynamic mechanical analysis, improving the compatibility between the flame retardant and PA6 matrix.

Thermal degradation behavior and flame retardant properties of PET/DiDOPO conjugated flame retardant composites.

PET/DIDOPO conjugated flame retardant composites were prepared by melt blending of styrene bridged DOPO (DIDOPO) into polyethylene terephthalate (PET). The flame retardancy, rheological behavior, and thermal degradation behavior of the composite were characterized by vertical combustion test (UL-94), limit oxygen index test (LOI), rotational rheometer, and thermogravimetry (TG). The results showed that the flame retardant composite with V-0 grade was obtained when the amount of DIDOPO is 12.5wt%, and the corresponding LOI value was 56.87% higher than that of PET. The thermogravimetry-fourier infrared spectroscopy (TG-FTIR) test results showed that DIDOPO could promote the degradation of PET/DIDOPO materials, and release phosphorus-containing free radicals to quench the flame, therefore slowing down the combustion process, and mainly playing the key flame retardant role in gas-phase.

Synthesis and Characterization of P-PPD-Ph-Conjugated Flame Retardant.

The conjugated flame retardants have rarely been studied. A conjugate flame-retardant 4, 4'-{1″, 4″-phenylene-bis [amino- (10‴-oxy10‴-hydro-9‴-hydrogen- 10‴λ5-phosphaphenanthrene-10″-yl)-methyl]}-diphenol (P-PPD-Ph) was synthesized and added into the polylactic acid (PLA) matrix. The P-PPD-Ph-conjugated flame-retardant structure was tested by FTIR, 1H, and 31P NMR analysis. The thermal and rheological properties of PLA/P-PPD-PH-conjugated flame-retardant composites were investigated. The results showed that P-PPD-Ph-conjugated flame retardant affects PLA/P-PPD-PH-conjugated flame-retardant composites for promoting the formation of a carbon layer when the P-PPD-Ph-conjugated flame-retardant content was 15% and the residual carbon ratio for PLA/P-PPD-PH-conjugated flame-retardant composites increased by 4.2%.

Flame Retardancy Properties and Rheological Behavior of PP/DiDOPO Conjugated Flame Retardant Composites.

A bridged 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide derivative (DiDOPO) with conjugated structure was utilized as a novel conjugated flame retardant, Polypropylene(PP)/DiDOPO conjugated flame retardant composites were papered by being melt-extruding with a twin-screw extruder. The flame retardant efficiency of PP/DiDOPO conjugated flame retardant composites were investigated by cone calorimetry, limiting oxygen index (LOI), vertical burning test (UL-94). Besides, the rheological behavior of PP/DiDOPO conjugated flame retardant composites are measured by ARES rheometer. The results showed that when the content of DiDOPO with conjugated structure was 16 wt%, the LOI values of PP/DiDOPO conjugated flame retardant composites was 24%, and PP/DiDOPO conjugated flame retardant composites reaches V-0 grade. The heat release rate (HRR), total heat release rate (THR) and CO2 of PP/DiDOPO conjugated flame retardant composites decreased, so PP/DiDOPO conjugated flame retardant composites had excellent flame retardant effect. Rheological analysis results indicated that DiDOPO with conjugated structure suppressed the melt dripping of PP/DiDOPO conjugated flame retardant composites by enhancing the melt stability. The results showed that the DiDOPO with conjugated structure can significantly enhance the flame retardancy effect of PP/DiDOPO conjugated flame retardant composites. In addition, the materials PP/DiDOPO might be with low conductivity and charge transport mobility.

Flame-Retardant Properties and Mechanism of Polylactic Acid-Conjugated Flame-Retardant Composites.

The DOPO derivative-conjugated flame retardant 4, 4'-{1'', 4'' - phenylene - bis [amino - (10‴ - oxy -10‴-hydro-9‴-hydrogen-10‴ λ5 -phosphaphenanthrene-10''-yl)-methyl]}-diphenol (P-PPD-Ph) with two hydroxyl groups was synthesized. Polylactic acid conjugated flame-retardant composites with P-PPD-Ph were papered by using a twin-screw extruder. The flame-retardant properties of polylactic acid-conjugated flame-retardant composites were investigated. The flame-retardant properties of PLA-conjugated flame-retardant composites were characterized by the limiting oxygen index (LOI) and the vertical burning test (UL94). The results showed that the PLA-conjugated flame-retardant composites achieved a V-0 rating (UL-94, 3.2 mm) when the conjugated flame retardant was added at 5 wt%, and increase in LOI value from 22.5% to 31.4% relative to composites without added conjugated flame retardant. The flame-retardant mechanism of PLA-conjugated flame-retardant composites were further studied by TG-FTIR, the results showed that the P-PPD-Ph promoted the PLA-conjugated flame-retardant composites to decompose and also released fragments with quenching and dilution, which suggests that P-PPD-Ph for PLA-conjugated flame-retardant composites mainly play a role of the gas-phase flame retardant.

Flexure-resistant and additive-free poly (L-lactic acid) hydrophobic membranes fabricated by slow phase separation.

PLLA membranes with excellent ductility were successfully prepared by a simple solvent evaporation-induced precipitation method, without any additive. The excellent mechanical properties are mainly attributed to the interconnecting pore morphology and the plastic deformation of the pore wall during the stretching process. The interconnecting pore morphology is determined by delaying non-solvent diffusion and molecular chain pre-nucleation. It was found that the average pore size gradually decreased from 19.25 µm to 6.71 µm as the concentration of the polymer solution increased from 0.03 g/ml to 0.10 g/ml, and the elongation at break of the membrane can reach 130.8%. The crystallinity is between 33.4% and 44.5%, and the crystal form is a perfect α crystal. Membrane with interconnecting pore structure contributes to the formation of 91.2% porosity. Furthermore, the solvent evaporation-induced precipitation method can also form surfaces containing micro-nano structures which significantly improves surface hydrophobicity. The combination of high porosity and hydrophobicity makes the membrane potentially applicable to the field of oil-water separation.

Directional Electromagnetic Interference Shielding Based on Step-Wise Asymmetric Conductive Networks.

Some precision electronics such as signal transmitters need to not only emit effective signal but also be protected from the external electromagnetic (EM) waves. Thus, directional electromagnetic interference (EMI) shielding materials (i.e., when the EM wave is incident from different sides of the sample, the EMI shielding effectiveness (SE) is rather different) are strongly required; unfortunately, no comprehensive literature report is available on this research field. Herein, Ni-coated melamine foams (Ni@MF) were obtained by a facile electroless plating process, and multiwalled carbon nanotube (CNT) papers were prepared via a simple vacuum-assisted self-assembly approach. Then, step-wise asymmetric poly(butylene adipate-co-terephthalate) (PBAT) composites consisting of loose Ni@MF layer and compact CNT layer were successfully fabricated via a facile solution encapsulation approach. The step-wise asymmetric structures and electrical conductivity endow the Ni@MF/CNT/PBAT composites with unprecedented directional EMI shielding performances. When the EM wave is incident from Ni@MF layer or CNT layer, Ni@MF-5/CNT-75/PBAT exhibits the total EMI SE (SET) of 38.3 and 29.5 dB, respectively, which illustrates the ΔSET of 8.8 dB. This work opens a new research window for directional EMI shielding composites with step-wise asymmetric structures, which has promising applications in portable electronics and next-generation communication technologies.

Preparation and Finite Element Analysis of Fly Ash/HDPE Composites for Large Diameter Bellows.

In recent years, buried bellows have often had safety accidents such as pipeline bursts and ground subsidence due to the lack of adequate mechanical properties and other quality problems. In order to improve the mechanical properties of bellows, fly ash (FA) was used as a reinforced filler in high density polyethylene (HDPE) to develop composites. The FA was surface treated with a silane coupling agent and HDPE-g-maleic anhydride was used as compatibilizer. Dumbbell-shaped samples were prepared via extrusion blending and injection molding. The cross-section morphology, thermal stability and mechanical properties of the composites were studied. It was observed that when 10% modified FA and 5% compatibilizer were added to HDPE, the tensile yield strength and tensile breaking strength of the composites were nearly 30.2% and 40.4% higher than those of pure HDPE, respectively, and the Young's modulus could reach 1451.07 MPa. In addition, the ring stiffness of the bellows was analyzed using finite element analysis. Compared with a same-diameter bellows fabricated from common commercially available materials, the ring stiffness increased by nearly 23%. The preparation method of FA/HDPE is simple, efficient, and low-cost. It is of great significance for the popularization of high-performance bellows and the high value-added utilization of FA.

Integrated analysis of miRNA-mRNA regulatory networks of potato (Solanum tuberosum L.) in response to cadmium stress.

Cadmium (Cd) stress is a ubiquitous abiotic stress affecting plant growth worldwide and negatively impacting crop yield and food safety. Potato is the most important non-grain crop globally, but there is limited research available on the response of this crop to Cd stress. This study explored the coping mechanism for Cd stress in potato through analyses of miRNA and mRNA. Tissue culture seedlings (20-day-old) of potato variety 'Atlantic' were cultured for up to 48 h in liquid medium containing 5 mmol/L CdCl2, and phenotypic, physiological, and transcriptomic changes were observed at specific times. With the extension of Cd stress time, the potato leaves gradually wilted and curled, and root salicylic acid (SA), glutathione (GSH), and lignin contents and peroxidase (POD) activity increased, while indole-3-acetic acid (IAA) and zeatin (ZT) contents decreased. Using miRNA-seq, 161 existing miRNAs, 383 known miRNAs, and 7361 novel miRNAs were identified, and, 18 miRNAs were differentially expressed in response to Cd stress. Based on mRNA-seq, 7340 differentially expressed mRNAs (DEGs) were found. Through mRNA-miRNA integrated analysis, miRNA-target gene pairs consisting of 23 DEGs and 33 miRNAs were identified. Furthermore, "glutathione metabolism" "plant hormone signal transduction" and "phenylpropanoid biosynthesis" were established as crucial pathways in the Cd stress response of potato. Novel miRNAs novel-m3483-5p and novel-m2893-5p participate in these pathways through targeted regulation of cinnamic alcohol dehydrogenase (CAD; PG0005359) and alanine aminotransferase (POP; PG0024281), respectively. This study provides information that will help elucidate the complex mechanism of the Cd stress response in potato. Moreover, candidate miRNAs and mRNAs could yield new strategies for the development of Cd-tolerant potato breeding.

Integration of mRNA and miRNA analysis reveals the molecular mechanism of potato (Solanum tuberosum L.) response to alkali stress.

The continuing increase in the global saline-alkali land area has made saline-alkali stress the principal abiotic stress limiting plant growth. Potato is the most important non-grain crop, and its production is also severely limited by saline-alkali stress. However, few studies have addressed the mechanism of saline-alkali tolerance of potato with a focus on its response to neutral salt NaCl stress, or its response to alkali stress. Recently, miRNA-mRNA analyses have helped advance our understanding of how plants respond to stress. Here, we have characterized the morphological, physiological, and transcriptome changes of tissue culture seedlings of potato variety "Qingshu No. 9" treated with NaHCO3 (for 0, 2, 6, and 24 h). We found that the leaves of tissue culture seedlings wilted and withered under alkali stress, and the contents of ABA, BRs, trehalose, and lignin in roots increased significantly. The contents of GAs decreased significantly. Subsequently, miRNA-seq analysis results identified 168 differentially expressed miRNAs (DEMIs) under alkali stress, including 21 exist miRNAs and 37 known miRNAs from 47 families and 110 novel miRNAs. The mRNA-seq results identified 5731 differentially expressed mRNAs (DEMs) under alkali stress. By miRNA-mRNA integrated analysis, were obtained 33 miRNA-target gene pairs composed of 20 DEMIs and 33 DEMs. Next, we identified the "phenylpropanoid biosynthesis", "plant hormone signal transduction", and "starch and sucrose metabolism" pathways as necessary for potato to respond to alkali stress. miR4243-x and novel-m064-5p were involved in the response of potato to alkali stress by their negative regulatory effects on shikimate O-hydroxycinnamoyltransferase (HCT) and sucrose-phosphate synthase (SPS) genes, respectively. The expression results of miRNA and mRNA were verified by quantitative real-time PCR (qRT-PCR). Our results clarify the mechanism of potato response to alkali stress at the miRNA level, providing new insights into the molecular mechanisms of potato's response to alkali stress. We report many candidate miRNAs and mRNAs for molecular-assisted screening and salt-alkali resistance breeding.

Crystallization Morphology Regulation on Enhancing Heat Resistance of Polylactic Acid.

To expand the use of polylactic acid (PLA) in high-temperature environments, crystallization morphology regulation was studied to enhance the heat resistance of PLA. PLA crystallinity was controlled using heat treatment and nucleating agent (zinc phenylphosphonate, brand TMC). The heat deflection temperatures of PLAs with same crystallinities considerably varied using different treatments. The crystallization morphology of PLA (4032D) and PLA/TMC composites was studied using X-ray diffraction (XRD) and polarized optical microscopy. XRD test results show that TMC can improve the crystallization rate and heat treatment can enhance the crystallinity and thickness of PLA, suggesting that the crystallization morphology improved after heat treatment. Nucleating agents can increase the crystallinity of PLA but cannot improve its crystallization morphology. The findings indicate that at the same crystallinity, PLAs exhibit improved crystallization morphology and high heat resistance; these results can provide guidance for improving the heat resistance of PLAs and facilitate the design of new nucleating agents.

Genome-wide analysis of lectin receptor-like kinases family from potato (Solanum tuberosum L.).

Lectin receptor-like kinases (LecRLKs) are involved in responses to diverse environmental stresses and pathogenic microbes. A comprehensive acknowledgment of the family members in potato (Solanum tuberosum) genome is largely limited until now. In total, 113 potato LecRLKs (StLecRLKs) were first identified, including 85 G-type, 26 L-type and 2 C-type members. Based on phylogenetic analysis, StLecRLKs were sub-grouped into seven clades, including C-type, L-type, G-I, G-II, G-III G-IV and G-V. Chromosomal distribution and gene duplication analysis revealed the expansion of StLecRLKs occurred majorly through tandem duplication although the whole-genome duplication (WGD)/segmental duplication events were found. Cis-elements in the StLecRLKs promoter region responded mainly to signals of defense and stress, phytohormone, biotic or abiotic stress. Moreover, expressional investigations indicated that the family members of the clades L-type, G-I, G-IV and G-V were responsive to both bacterial and fungal infection. Based on qRT-PCR analysis, the expressions of PGSC0003DMP400055136 and PGSC0003DMP400067047 were strongly induced in all treatments by both Fusarium sulphureum (Fs) and Phytophthora infestans (Pi) inoculation. The present study provides valuable information for LecRLKs gene family in potato genome, and establishes a foundation for further research into the functional analysis.

Genome-wide analysis and expression profiles of the StR2R3-MYB transcription factor superfamily in potato (Solanum tuberosum L.).

MYB transcription factors comprise one of the largest families in plant kingdom, which play a variety of functions in plant developmental processes and defence responses, the R2R3-MYB members are the predominant form found in higher plants. In the present study, a total of 111 StR2R3-MYB transcription factors were identified and further phylogenetically classified into 31 subfamilies, as supported by highly conserved gene structures and motifs. Collinearity analysis showed that the segmental duplication events played a crucial role in the expansion of StR2R3-MYB gene family. Synteny analysis indicated that 37 and 13 StR2R3-MYB genes were orthologous to Arabidopsis and wheat (Triticum aestivum), respectively, and these gene pairs have evolved under strong purifying selection. RNA-seq data from different tissues and abiotic stresses revealed tissue-preferential and abiotic stress-responsive StR2R3-MYB genes. We further analyzed StR2R3-MYB genes might be involved in anthocyanin biosynthesis and drought stress by using RNA-seq data of pigmented tetraploid potato cultivars and drought-sensitive and -tolerant tetraploid potato cultivars under drought stress, respectively. Moreover, EAR motifs were found in 21 StR2R3-MYB proteins and 446 pairs of proteins were predicted to interact with 21 EAR motif-containing StR2R3-MYB proteins by constructing the interaction network with medium confidence (0.4). Additionally, Gene Ontology (GO) analysis of the 21 EAR motif-containing StR2R3-MYB proteins was performed to further investigate their functions. This work will facilitate future biologically functional studies of potato StR2R3-MYB transcription factors and enrich the knowledge of MYB superfamily genes in plant species.

Fabrication of reinforced and toughened PC/PMMA composites by tuning the migration and selective location of graphenes during melt blending.

In this work, we creatively obtained reinforced and toughened PC/PMMA/GNs composites by tuning the migration and selective location of graphene nanosheets (GNs) during melt blending. TEM results revealed that the migration of GNs in PC/PMMA blends during melt blending always existed no matter how the GNs were introduced, and most of them exclusively localized at the interface of PC and PMMA phase due to interfacial effects. The migration of GNs could refine the size of the dispersed phase, and the exclusive localization of GNs at the interface show obvious interfacial compatibilizing effects, leading to improved mechanical properties of the composites. It was found that the composite prepared by one-step compounding showed significant enhanced strength and toughness with addition of mere 0.05 wt% GNs and the tensile strength and elongation of the composite increased by about 62.96% and 94.54%, respectively as compared to the PC/PMMA blends. Moreover, the composite prepared by one-step compounding also showed improved thermal conductivity at the same time, indicating excellent comprehensive properties. It is believed that tuning the migration and selective localization of GNs open perspectives for the development of high-performance polymer composites.

RNA Sequencing Reveals That Both Abiotic and Biotic Stress-Responsive Genes are Induced during Expression of Steroidal Glycoalkaloid in Potato Tuber Subjected to Light Exposure.

Steroidal glycoalkaloids (SGAs), which are widely produced by potato, even in other Solanaceae plants, are a class of potentially toxic compounds, but are beneficial to host resistance. However, changes of the other metabolic process along with SGA accumulation are still poorly understood and researched. Based on RNA sequencing (RNA-seq) and bioinformatics analysis, the global gene expression profiles of potato variety Helan 15 (Favorita) was investigated at four-time points during light exposure. The data was further verified by using quantitative Real-time PCR (qRT-PCR). When compared to the control group, 1288, 1592, 1737, and 1870 differentially expressed genes (DEGs) were detected at 6 h, 24 h, 48 h, and 8 d, respectively. The results of both RNAseq and qRT-PCR showed that SGA biosynthetic genes were up-regulated in the potato tuber under light exposure. Functional enrichment analysis revealed that genes related to PS light reaction and Protein degradation were significantly enriched in most time points of light exposure. Additionally, enriched Bins included Receptor kinases, Secondary metabolic process in flavonoids, Abiotic stress, and Biotic stress in the early stage of light exposure, but PS Calvin cycle, RNA regulation of transcription, and UDP glucosyl and glucoronyl transferases in the later stage. Most of the DEGs involved in PS light reaction and Abiotic stress were up-regulated at all four time points, whereas DEGs that participated in biotic stresses were mainly up-regulated at the later stage (48 h and 8 d). Cis-element prediction and co-expression assay were used to confirm the expressional correlation between genes that are responsible for SGA biosynthesis and disease resistance. In conclusion, the expressions of genes involved in PS light reaction, Abiotic stress, and Biotic stress were obviously aroused during the accumulation of SGAs induced by light exposure. Moreover, an increased defense response might contribute to the potato resistance to the infection by phytopathogenic microorganisms.